This standard is issued under the fixed designation C; the number 1 This test method is under the jurisdiction of ASTM Committee B08 on Metallic. ASTM C determines the bonding strength of thermal spray coatings. ASTM Standard C, “Standard Test Method for Adhesion or Cohesive Strength of Flame-Sprayed Coatings,” is widely used in industry and research for .

Author: Sarisar Taukree
Country: Lesotho
Language: English (Spanish)
Genre: Spiritual
Published (Last): 22 August 2007
Pages: 424
PDF File Size: 17.62 Mb
ePub File Size: 18.86 Mb
ISBN: 767-9-25024-659-2
Downloads: 64365
Price: Free* [*Free Regsitration Required]
Uploader: Dajar

To ensure the direction of force application is perpendicular to the coated surfaces, ASTM C specifies to use a self-aligning load fixture to attach awtm substrate cylinders to the test frame. NOTE 3—When liquid epoxy bonding agents are used, there should be a procedure in place to ensure relatively consistent thickness on every sample.

ASTM C – DFD® Instruments

The substrate fixture that spray coating is applied to is most astm c a cylinder made of the same metal that would be used as the satm of the coating in its actual use.

The maximum force is then normalized over the cross-sectional area to give adhesion or cohesion strength of the thermal spray.

The substrate generally is a metal, but may be a ceramic, such as an oxide or graphite. Sistemas para Ensaios Automatizados.


Because of residual stresses in thermal spray coatings, actual strength depends upon the shape of the particular coated part. One end of each? Contact Us View Accessories Catalog.


The test consists of coating one face of a substrate? The maximum force is then normalized over the cross-sectional adtm to give adhesion or cohesion strength of the thermal spray.

Originally published as C — The method works but is associated with a number of drawbacks: With The ASTM standard the rate of stress increase in the coating will depend on the thickness of the coating, which is another weakness of this standard: Further development may establish that thin layers of certain types of especially dense coatings may be tested satisfactorily.

The stress increase should be the same regardless of coating thickness! Alternatively, new adhesive bonding agents that would allow reduction of the minimum thickness limitation may become available. The entire ASTM C63 specification should astm c reviewed prior astm c performing the test to c33 correct substrate surface preparation, application of coatings and test speeds.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. The stress increase should be the same regardless of asgm thickness! Finish the coating surface if required.

It is the responsibility of the user c63 this standard to establish appropriate safety and health limitations prior to use. The adhesive bonding agent should not be the “weakest link”, but should be at least as strong as the minimum required adhesion or cohesion strength of d633 coating. The Problems The method works but is associated with a number of drawbacks: Bluehill Universal Brochure Bluehill Universal Software is built from the astm c for touch interaction sstm an intuitive astm c experience.


They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. Your comments are invited either for revision of this standard or for additional standards and aastm be addressed to ASTM Headquarters. A similar, but uncoated, fixture is then glued to the surface of the coating with a suitable adhesive astm c agent. Those bonding agents established so far for this method tend to penetrate thermal spray coatings and may invalidate results unless the coatings are thick enough to prevent penetration through the coating.

The strain in a thin coating cannot be sensibly measured so tensile astm c in millimeters per minute is not relevant. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address sstm at phonefaxor service astm.

Your choices will not impact your visit. These parameters were originally set because of the limitations astm c ashm testing machines.


Usually manufacturers of the coatings have recommendations published or available. Email addresses must contain the symbol. In addition, prepare one set of uncoated? The assembly is pulled at a constant speed between 0. Contact Us Request an Accessory Catalog.

Subscribe US Now