Cerber C52 is a burglar alarm system with 6 fully programmable zones on the motherboard, expandable to 12 by doubling and / or using keypad zones (each. Cerber c Users Guide – Download as PDF File .pdf), Text File .txt) or read online. Cerber C Zone and 2-Partition Burglary Control Panel For your home and office User’s Guide Doc / / version 1. INTRODUCTION.

Author: Malazil Moogur
Country: Madagascar
Language: English (Spanish)
Genre: Spiritual
Published (Last): 10 December 2005
Pages: 255
PDF File Size: 20.76 Mb
ePub File Size: 5.46 Mb
ISBN: 207-8-47456-389-8
Downloads: 97275
Price: Free* [*Free Regsitration Required]
Uploader: Meztizragore

To bypass a zone press the key which corresponds to the zone number and the appropriate LED will turn ON. Before entering this command the PC modem must be already on the phone line and call the control panel. If the system is ready cetber the button is pressed, the system will arm; Pressing the button again will disarm the system. Please note that the keypad is programmed to emit intermittent beeps at every 8 seconds, whenever a trouble condition occurs for first time.

If the buzzer warnings were enabled by programming, during the exit delay time, the keypad buzzer will sound warning beeps.

The following operations cwrber be performed: A ZNot k6 BypassZ part. In order to enter zone bypassing menu, the user should enter one of the commands: If after entering the last digit of the user code the keypad buzzer is sounding a long rejection beep means: Crrber if no successful command was performed, the user should press [ ] key in order to exit from the display of PGM1 to PGM6 status. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers.

By pressing [1] key you can see the 1-st alarm and by pressing [9] key you can see the 9-th alarm. In order to program the selected phone number, you should enter maximum 15 digits as you ferber on a key phone.

In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson.

Press [ ] key to exit zone-bypassing menu.

Quick Arming Modes Arming without user codes Quick arming features allow the system to be quickly armed by any person who may not own a user code. In a partitioned system, in order to arm a partition by users assigned to only one partition, simply key in a valid user code; the corresponding partition will arm after exit time. The keypad buzzer will sound 3 beeps after each 2-digit group and 6 beeps after the last one.


After all sensors in the system was tested, f612 [ ] key to exit this testing mode. Press [ ] key to exit system trouble displaying menu.

Section [] — Walk Test service mode Moreover, smoke detectors have sensing limitations.

Cerber C – Roel Design

The programming sections allowed to the master user are: While PC modem is calling the control panel, just entering this command will manually activate the communication between PC and panel. To cancel the command user can press [ ] key. This command is accepted only while the system is partially armed.

This trouble indicator will turn OFF only after programming cerbr system time and date.

Zone LEDs a While the system is completely armed: Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliances, or by passing traffic.

If any trouble condition occurs, it needs to be solved before arming to assure a proper function for system. This trouble indicates that the battery is disconnected or its voltage is lower than The keypad will confirm entering this mode with 3 beeps.

Keypad types The next keypad models are available: No smoke detector can sense every kind of fire every time. For each key pressing, the keypad buzzer will sound a short beep. The PGM1 to PGM6 output will change again their status when the system clock is identical with the time established in corresponding sections from [] to [].

Cerber c Users Guide – Documents

In a partitioned system, entering any of quick arming commands is followed by a time of 5 seconds in which the the user has to choose the disarmed partitions to be armed without codes; to arm the A partition the user must press [1] key and to arm the B partition the user must press [2] key please note that if ccerber user is pressing the key which corresponds to an armed partition, the keypad buzzer will sound a long ceeber.


At the end of the exit delay time, after such an arming mode, the zones which are usually of the perimeter delayed type will respond as instant zones they will trigger the alarm as soon as they will be violated.

The BELL output uses a fuseless circuit and it 6c12 automatically shut down if the current exceeds 2. The most frequent cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance.

The following sequence will be introduced: The control panel can report upon remote interrogation calls and to the follow me phone numbers, too up to 8 voice messages only when there it is using the MPV8 voice module; voice messages are specific to alarms on 1 to 8 1zones. Programming of the system time and date can be canceled by [ ] key pressing. They do not create multiple beams of protection and intrusion can cedber be detected in unobstructed areas covered by the beams.

For each these times any value from to may be entered, but the panel will automatic adjust the introduced value by modulo and will record the result in memory as programmed value.

Partitioning can be used in installations where shared security systems are more practical, such as home offices or warehouse buildings. After setting these options, press [ ] key to ceber. This command is similar to the one in the 6c12 programming section [].

Cerber c612 Users Guide

Once a delayed zone is first violated during one armed period it will start the appropriate entry delay timer; the keypad buzzer will sound a continuous beep, indicating that the system must be disarmed. The cerver will come back in the stand-by state, waiting for commands.

Mechanical tampering, masking, painting, or spraying of any material on the mirrors, windows or any part of the optical system can reduce detection ability.

Subscribe US Now