INTERSEAL 670HS MSDS PDF

admin

INTERSEAL HS – PART B (REGULAR) – L () Use; Colors; MSDS / TDS; Variant; Product Review(s). Use For immersion service, Interseal HS must be applied to surfaces blast cleaned to SSPC-SP10 or Sa PT. International Paint Indonesia. Safety Data Sheet EGA INTERSEAL HS GREY PART A Version Number 2 Revision Date 06/27/ 1. Product and . International Paint Ltd. Safety Data Sheet. EGA Interseal HS Grey Part A. Version No. 2 Date Last Revised 05/10/ Conforms to the requirements of.

Author: Shaktiramar Aragore
Country: Syria
Language: English (Spanish)
Genre: Sex
Published (Last): 22 September 2014
Pages: 477
PDF File Size: 14.17 Mb
ePub File Size: 20.62 Mb
ISBN: 794-7-32498-309-2
Downloads: 71036
Price: Free* [*Free Regsitration Required]
Uploader: Fenrigor

NSF Certification is for tanks greater than gallons Interseal HS can be used as a non-skid deck system by modification with addition mads GMA crushed flint aggregate.

Avoid using a mixture of application methods whenever possible. However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used.

Consult International Protective Coatings for 670ha details. Prior to paint application all surfaces should be assessed and treated in accordance with ISO It is also possible to apply to damp surfaces in some circumstances. Premature exposure to ponding water intersela cause a color change, especially in dark colors. Warning In order to achieve optimum performance on hand prepared steel, the aluminum pigmented version should be applied as a primer coat by intersexl to ensure thorough wetting out of the substrate by Interseal HS.

  EM4095 DATASHEET PDF

Aged Coatings Interseal HS is suitable for overcoating a limited range of intact, tightly adherent aged coatings. Provides excellent anti-corrosive protection in industrial, coastal structures, pulp and paper plants, bridges and offshore environments in both interseao exposure and immersion service. Preferred application is by a suitable large tip hopper gun e. Alternatively, a broadcast method of application can be used.

Typical thicknesses will be between milsmicrons. A low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. Always mix a complete unit in the proportions supplied.

INTERSEAL 670HS – PART B (REGULAR) – 0.57L (5.63 :1)

Brush Typically mils interxeal can be achieved Roller 6700hs mils microns can be achieved How to use Mixing Material is supplied in two containers as a unit. In common with all epoxies Interseal HS will chalk and discolor on exterior exposure. Interseal HS is suitable for overcoating intact, aged alkyd, epoxy and polyurethane systems. However, these phenomena are not detrimental to anti-corrosive performance. For application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings.

Soluble salts should be removed by fresh water washing. Press and move to zoom. Further information is available from International Protective Coatings.

INTERSEAL HS – PART B (REGULAR) – L ( :1)

Puddles, ponding and accumulations of water must be removed. When applying by methods other than airless spray, the required film build is unlikely to be achieved. Level of sheen and surface finish is dependent on application method. Typically this would apply to C or D grade rusting in this standard. With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet.

  LINN AV5103 PDF

Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. Please 670hw International Protective Coatings for alternative recommendations.

interdeal

However, it can be used over suitably primed surfaces. Systems recommendation Interseal HS will normally be applied to correctly prepared steel substrates. Low or high temperatures may require specific application techniques to achieve maximum film build.

Application should then be to a suitably primed surface.

Mouse over image to zoom. Be the first to write a review for this product! The surface to be coated should be clean, dry and free from contamination. Surface preparation The performance of this product will depend upon the degree of surface preparation. Once the unit has been mixed it must be used within the working pot life specified.

Subscribe US Now