INTERSEAL 670HS MSDS PDF

admin

INTERSEAL HS – PART B (REGULAR) – L () Use; Colors; MSDS / TDS; Variant; Product Review(s). Use For immersion service, Interseal HS must be applied to surfaces blast cleaned to SSPC-SP10 or Sa PT. International Paint Indonesia. Safety Data Sheet EGA INTERSEAL HS GREY PART A Version Number 2 Revision Date 06/27/ 1. Product and . International Paint Ltd. Safety Data Sheet. EGA Interseal HS Grey Part A. Version No. 2 Date Last Revised 05/10/ Conforms to the requirements of.

Author: Daikinos Shagal
Country: Honduras
Language: English (Spanish)
Genre: Health and Food
Published (Last): 14 August 2009
Pages: 53
PDF File Size: 3.63 Mb
ePub File Size: 15.91 Mb
ISBN: 883-2-69357-413-6
Downloads: 21580
Price: Free* [*Free Regsitration Required]
Uploader: Taujinn

A low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. For application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings.

Provides excellent anti-corrosive protection in industrial, coastal structures, pulp and 67hs plants, bridges and offshore environments in both atmospheric exposure and immersion service.

NSF Msdw is for tanks greater than gallons Varnish Hybrid Water base.

INTERSEAL HS – PART B (REGULAR) – L ( :1)

Press and move to zoom. Mouse over image to zoom. Be the first to write a review for this product!

Surface preparation The performance of this product will depend upon msda degree of surface preparation. The surface to be coated should be clean, dry and free from contamination.

Prior to paint application all surfaces should be assessed and treated in accordance with ISO Accumulated dirt and soluble salts must be removed. Dry bristle brushing will normally be adequate for accumulated dirt.

  CLOSTRIDIOSES EM BOVINOS PDF

Soluble salts should be removed by fresh water washing. Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. A surface profile of mils microns is recommended. Typically this would apply to C or D grade rusting in this standard.

670ha It is also possible to apply to damp surfaces in some circumstances. Further information is available from International Protective Coatings. Aged Coatings Interseal HS is suitable for overcoating a limited range of intact, tightly adherent aged coatings. Loose or flaking coatings should be removed intersseal to a firm edge.

Systems recommendation Interseal HS will normally be applied to correctly prepared steel substrates. However, it can be used over suitably primed surfaces. When applying by methods msdw than airless spray, the required film build is unlikely to be achieved. Low or high temperatures may require specific application techniques to achieve maximum film build.

Brush Typically mils microns can be achieved Roller Typically mils microns can be achieved How to use Mixing Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied.

Once the unit has been mixed it must be used within the working pot life specified. Do not thin more than allowed by local environmental legislation. Warning In order to achieve optimum performance on hand prepared steel, the aluminum pigmented version should be applied as a primer coat by brush to ensure thorough wetting out of the substrate by Interseal Intrseal.

INTERSEAL 670HS – PART B (REGULAR) – 0.57L (5.63 :1)

If salt water is used in the wet blast process the resulting surface must be thoroughly washed with fresh water before application of Interseal HS. With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet. Puddles, ponding and accumulations of water must be removed.

  DOLINA UMARLYCH PDF

Interseal HS is suitable for overcoating intact, aged alkyd, epoxy and polyurethane systems. However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used. Please consult International Protective Coatings for alternative recommendations. Level of sheen and surface finish is dependent on application method. Avoid using a mixture of application methods whenever possible. In common with all epoxies Interseal HS will chalk and discolor on exterior exposure.

However, these phenomena are not detrimental to anti-corrosive performance. Premature exposure to ponding water will cause a color change, especially in dark colors.

Interseal HS can be used as a non-skid deck system by modification with addition of GMA crushed flint aggregate. Application should then be to a suitably primed surface. Typical thicknesses will be between milsmicrons.

Preferred application is by a suitable large tip hopper gun e. Sagola or Air texture 670hx fitted with a mm nozzle. Trowel or roller can be used for small areas.

Alternatively, a broadcast method of application can be used. Consult International Protective Coatings for further details. Certification is for tanks greater than gallons

Subscribe US Now