Objetivo: ISO specifies the properties and performance of sterile single-use hypodermic syringes with or without needle, made of plastic materials . Find the most up-to-date version of ISO at Engineering Sterile hypodermic syringes for single use – Part 3: Auto-disable syringes for fixed -dose immunization (ISO ); German version EN ISO
|Country:||Sao Tome and Principe|
|Published (Last):||21 October 2008|
|PDF File Size:||7.70 Mb|
|ePub File Size:||20.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
Review of Indian Standards Amendments are issued to standards as the need arises on the basis of comments. Needle tubing shall be in accordance with ISO Adjust the relative positions of the syringe and reservoir so that the water level in the reservoir 78863 approximately level with the mid-point of the syringe barrel- B.
Attention is particularly drawn to the following: The preparation of this standard was recognized as a high priority requirement to prevent the re-use of fixed dose immunization syringes in the developing and transitional countries. Syringes for manual use ISO This Indian Standard has been developed from Doc No.: Other standards can be applicable when syringes are used for any other intended purpose than those specified in ISO These lines shall be of uniform thickness.
Connect the nozzle of the syringe to the tubing of the reservoir B.
Upon delivering a fixed dose of vaccine, the syringe is automatically rendered unusable. The timing of the activation of the auto-disable feature may vary by design, typically within the ranges described below: Certain conventions are, however, not identical to those used in Indian Standards.
Using the test device C.
The piston shall not become detached from the plunger when tested in accordance sio Annex B of ISO When a syringe with integrated needle is tested in accordance with Annex 8 of ISO The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.
This part of JSO is not applicable to syringes for use with insulin specified in ISOsyringes made of glass specified in ISOsyringes for use with power-driven syringe pumps specified in ISOauto- disable syringes for variable dose delivery and syringes designed to be prefilled.
МКС EN ISO 7886-3:2011
It is recognized that syringes designed to reduce the risk of needlestick injuries, in addition to preventing sharps injuries, may also comply with this part of standard with regard to their auto-disable properties, but it is stressed that anti-needlestick properties of syringes are not in themselves addressed in this standard. This part of ISO does not specify the design of the auto-disable feature, which is left to the discretion of the manufacturer.
Follow these links to find other Standards similar to the one you are viewing. These syringes are not covered by Parts 1 and 2 of this standard. The corresponding Indian Standards which are to be substituted in their places are listed below along with their degree of equivalence for the editions indicated: It is designed to cover every economic sector and virtually every activity of the humankind where technical standards may be used.
It should not be possible to defeat the auto-disable feature by removing and re-inserting the plunger. Adjust the relative positions of the syringe and reservoir so that the water level in the reservoir is approximately level with the mid-point of the syringe barrel.
For undated references, the latest edition of the referenced document including any amendments applies.
BS EN ISO 7886-3:2009
Connect the needle of the syringe to the rubber stopper of the tubing of the reservoir B. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations.
The plunger should be of a length adequate to allow the piston properly to deliver the designated fixed dose. Summary This part of ISO specifies the properties and performance of sterile single-use hypodermic iiso withor without needle, made of plastic materials and stainless steel and intended for the aspiration of vaccines orfor the injection of vaccines immediately after filling.
Do you want to buy this document? Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of ‘BIS Catalogue’ and ‘Standards; Monthly Additions’.
NBN EN ISO | NBN
This part isp ISO is not applicable to syringes for use with insulin specified in ISOsyringes madeof glass specified in ISOsyringes for use with power-driven syringe pumps specified in ISO ,auto-disable syringes for variable dose delivery and syringes designed to be prefilled. Re-use of injection equipment in the absence of sterilization has increasingly let to transmission of blood-borne pathogens this standard.
Details Norm ISO nr: Sterile hypodermic needles for single use ISO Syringes for manual use IS For the purpose of deciding whether a particular requirements of isl standard is complied with, the final value, observed or calculated expressing the result of a test or analysis, shall be 786-3 off in accordance with IS 2: Syringes with re-use ixo feature Get the latest version of this product.
When the fiducial line of the piston coincides with the zero graduation line, the preferred minimum length of the plunger from the surface of the finger grips nearer to the push-button shall be 8 mm. Search the history of over billion web pages on the Internet.